Ice-O-Matic ice maker repair
Ice-O-Matic Ice Maker Repair in Downtown, the Strip & Uptown, Pittsburgh
We test your Ice-O-Matic ice maker where it's installed in Downtown, Strip District & Uptown, name the part that failed, and quote before any repair.
Rather type than call? Add the ice-o-matic ice maker's model number and where you are in Downtown, Strip District & Uptown, and we'll check parts before the visit.
Two quick steps: what's wrong and where you are. We'll be in touch to set a time.
ice maker brands we repair
Ice-O-Matic Ice Maker Repair in Houses, Apartments and Rentals
Coverage here takes in ZIPs 15219, 15222. We work independently and aren't affiliated with Ice-O-Matic, so a unit still under the maker's warranty should go to Ice-O-Matic first. Keep the model number close by when you get in touch.
How an Ice Maker Repair Visit Works
Describe the Problem
The brand, the model number if it's handy, and what the appliance is doing. A photo of the rating label is a bonus.
Diagnosis On Site
The technician tests the appliance and its power, water, drain, gas or vent until the failed part is found.
Explanation and Quote
You hear what failed and what the repair costs, then decide. Nothing starts without your OK.
Repair and Test
The part goes in, the appliance runs a cycle, and you see that it works before we leave.
Related Services
Other appliances, brands and places we cover.
Ice-O-Matic Ice Maker Symptoms We Track Down
The same complaint can come from more than one part. We test on site to find which one before quoting.
- Not Making Ice
- Making Small or Hollow Ice Cubes
- Leaking Water
- Ice Tastes or Smells Bad
- Overfilling with Ice
- Making Loud Noise
- Producing Too Little Ice
- Ice Clumping Together
- Water Leaking from Ice Maker
- Ice Not Dispensing
- Ice Has Bad Taste or Odor
- Producing Small or Hollow Ice Cubes
- Ice Cubes Appear Cloudy
- Ice Maker Overflowing Bin
- Drain Pump Failure
- Freezing Section Not Cold Enough
- Condenser Dirty Reducing Efficiency
- Water Inlet Valve Failure
- Ice Maker Freezing Up Internally
- Ice Maker Unit Won't Turn On
- Ice Bin Agitator Motor Failure
- Scale Buildup in Water Lines
- Ice Production Drops in Summer
- Ice Harvest Cycle Too Slow
- Water Pump Failure
- Evaporator Coil Iced Over
- Ice Cubes Inconsistent Size
- Water Reservoir Overflowing
- Control Board Failure
- Hot Gas Harvest Valve Failure
- Water Distribution Tube Clogged
- Not Making Cube Ice — Making Flakes Instead
- Nugget Ice Maker Not Producing Nuggets
- Ice Maker Tripping Circuit Breaker
- Ice Maker Needs Sanitizing
- Scale Buildup on Evaporator Plate
- Compressor Starting Problems
- Water Flowing Constantly into Ice Maker
- Ice Stuck in Mold / Won't Release
- Water Line Taste Affecting Ice
- Outdoor Ice Maker Not Working Right
- Nugget Ice Maker Scale Buildup
- Ice Maker Smells Musty
- Not Reaching Rated Ice Production
- Ice Forming Outside the Bin
- Ice Maker Making Loud Operation Noise
- Ice Production Varies Seasonally
- Water Not Circulating Over Evaporator
- Slime or Mold Inside Ice Machine
- Error Code on Ice Maker Display
- Condensate Drain Clogged
- Not Stopping When Bin Is Full
- Portable Countertop Ice Maker Problems
- Is an Older Ice Maker Worth Repairing?
Ice Maker Makes We Also Repair
More Ice-O-Matic Products
About Ice-O-Matic ice maker repairs here
Ice-O-Matic ice maker repair in all 2 Downtown, Strip District & Uptown ZIP codes: diagnosis in your home, then a price for you to accept before anything is done.
A call here is more likely to involve a freight elevator than a driveway. Downtown and the Strip have filled up with apartments over the past two decades, many of them inside buildings that started life as offices, warehouses or department stores, so the appliances are newer than the walls and the plumbing runs a long way. Up the hill, the Hill District and Uptown are rowhouse and walk-up country, where the questions are steps, parking and older service lines.
On an Ice-O-Matic ice maker we check the supply line, then the fill valve, then the harvest parts, because small, hollow or cloudy cubes and poor output nearly always come down to water flow or mineral buildup. Also worth knowing: Ice-O-Matic makes commercial cubers, and the water going into one decides a great deal about how long it lasts.
Call or book online and we'll set up a time that works for you.
Inside an Ice-O-Matic ice maker
An Ice-O-Matic cuber freezes water over a vertical evaporator, with a pump circulating water from a trough across the plate. An ice thickness probe senses when the ice has built to the set size and signals the board to harvest; hot gas then warms the evaporator so the slab of cubes drops into the bin. Water level sensing in the trough controls how much water each cycle uses, and a bin control stops production when the bin is full. When scale coats the evaporator or the probe, harvest timing goes wrong: cubes grow too thick, stick, or release as a single sheet. Pearl Ice and flaker models use an auger instead, with their own wear points in the gear motor and bearings.
One more point: an Ice-O-Matic with slow harvests or shrinking cubes usually wants a descale or a clean condenser before it wants a part.
Common Ice-O-Matic ice maker failures
What we look at first on this pairing: Scale on evaporator and thickness probe; Water pump weak; Ice thickness probe dirty or misadjusted; Bin control not sensing full; Water inlet valve failing.
That's where we start, not a verdict. The same complaint can come from an inexpensive part or a costly one, which is why the cause is confirmed in your home before any price is given.
Ice-O-Matic ice makers in Downtown, Strip District & Uptown homes
In Downtown, Strip District & Uptown's apartments a ice maker is frequently counter-depth or panel-fronted, breathing through a slim grille at the bottom. Keep that grille clear; blocking it is the quickest way to make a built-in run warm.
Wherever a ice maker has a water line in an apartment, we check the shutoff and the supply tube each visit; a slow drip there can reach the neighbor's ceiling before you see it.
The ice maker fault people misjudge
Across brands, the ice maker symptom that misleads people most is an ice maker declared dead when the real problem is a line crushed behind the refrigerator, a line frozen along an outside wall, or a fill-valve screen clogged with scale.
In Downtown, Strip District & Uptown, the local condition that matters most for a ice maker is long water lines run up from the basement through the kitchen floor, lines that freeze in a cold snap, and scale collecting in the fill valve.
Cold garages and winter refrigerators
A refrigerator in an unheated space works on the edge of its design. In summer it runs constantly; in January it may hardly run at all, and a freezer that depends on the fresh-food thermostat thaws.
Before paying for a repair on a garage unit, check the manual's ambient-temperature range. We'll check it too, and tell you if the location is the actual problem.
Ice-O-Matic Ice Maker in Downtown, Strip District & Uptown, by the numbers
Ice-O-Matic Ice Maker: Questions We Hear
Quick answers to what people ask most. If yours isn't here, bring it up on the phone or type it into the notes box when you book.
Something else on your mind?
Reach out with the brand, the symptom and a model number if you have one. Some questions we can answer on the spot; the rest a technician can check in person.
Not at all. Most repairs are done where the machine stands, and around Downtown, Strip District & Uptown laundry is usually in a closet in the unit, usually as a stacked or 24-inch pair, or a shared laundry room on another floor of the building. If the stairs are very narrow or steep, tell us when you book so we can plan for anything that might need to come out.
Many refrigerators and some freezers are designed for a heated room, and in an unheated Downtown, Strip District & Uptown garage the controls may not run the compressor enough on the coldest days. The owner's manual lists the temperature range your model was built for. We'll check whether it's the location or a fault before quoting anything.
That depends on what broke. A switch, valve, pump or element is a small fraction of what a control board or sealed-system job runs; you get the figure once it's diagnosed and before any work.
Often, if we have the model number beforehand. Ice-O-Matic shares a parts bin with the other Commercial brands, so compatible parts are usually easy to get, even for older units. Parts that must be ordered come with a lead time you hear before deciding.