Ice-O-Matic ice maker repair
Ice-O-Matic Ice Maker Repair in West End, Crafton & Carnegie, PA
We test your Ice-O-Matic ice maker where it's installed in West End, Crafton & the Airport Corridor, name the part that failed, and quote before any repair.
Rather type than call? Add the ice-o-matic ice maker's model number and where you are in West End, Crafton & the Airport Corridor, and we'll check parts before the visit.
Two quick steps: what's wrong and where you are. We'll be in touch to set a time.
ice maker brands we repair
Ice-O-Matic Ice Maker Repair in Houses, Apartments and Rentals
Coverage here takes in ZIPs 15204, 15205, 15220, 15225, 15106. We work independently and aren't affiliated with Ice-O-Matic, so a unit still under the maker's warranty should go to Ice-O-Matic first. Keep the model number close by when you get in touch.
How an Ice Maker Repair Visit Works
Describe the Problem
The brand, the model number if it's handy, and what the appliance is doing. A photo of the rating label is a bonus.
Diagnosis On Site
The technician tests the appliance and its power, water, drain, gas or vent until the failed part is found.
Explanation and Quote
You hear what failed and what the repair costs, then decide. Nothing starts without your OK.
Repair and Test
The part goes in, the appliance runs a cycle, and you see that it works before we leave.
Related Services
Other appliances, brands and places we cover.
Ice-O-Matic Ice Maker Symptoms We Track Down
The same complaint can come from more than one part. We test on site to find which one before quoting.
- Not Making Ice
- Making Small or Hollow Ice Cubes
- Leaking Water
- Ice Tastes or Smells Bad
- Overfilling with Ice
- Making Loud Noise
- Producing Too Little Ice
- Ice Clumping Together
- Water Leaking from Ice Maker
- Ice Not Dispensing
- Ice Has Bad Taste or Odor
- Producing Small or Hollow Ice Cubes
- Ice Cubes Appear Cloudy
- Ice Maker Overflowing Bin
- Drain Pump Failure
- Freezing Section Not Cold Enough
- Condenser Dirty Reducing Efficiency
- Water Inlet Valve Failure
- Ice Maker Freezing Up Internally
- Ice Maker Unit Won't Turn On
- Ice Bin Agitator Motor Failure
- Scale Buildup in Water Lines
- Ice Production Drops in Summer
- Ice Harvest Cycle Too Slow
- Water Pump Failure
- Evaporator Coil Iced Over
- Ice Cubes Inconsistent Size
- Water Reservoir Overflowing
- Control Board Failure
- Hot Gas Harvest Valve Failure
- Water Distribution Tube Clogged
- Not Making Cube Ice — Making Flakes Instead
- Nugget Ice Maker Not Producing Nuggets
- Ice Maker Tripping Circuit Breaker
- Ice Maker Needs Sanitizing
- Scale Buildup on Evaporator Plate
- Compressor Starting Problems
- Water Flowing Constantly into Ice Maker
- Ice Stuck in Mold / Won't Release
- Water Line Taste Affecting Ice
- Outdoor Ice Maker Not Working Right
- Nugget Ice Maker Scale Buildup
- Ice Maker Smells Musty
- Not Reaching Rated Ice Production
- Ice Forming Outside the Bin
- Ice Maker Making Loud Operation Noise
- Ice Production Varies Seasonally
- Water Not Circulating Over Evaporator
- Slime or Mold Inside Ice Machine
- Error Code on Ice Maker Display
- Condensate Drain Clogged
- Not Stopping When Bin Is Full
- Portable Countertop Ice Maker Problems
- Is an Older Ice Maker Worth Repairing?
Ice Maker Makes We Also Repair
More Ice-O-Matic Products
About Ice-O-Matic ice maker repairs here
Ice-O-Matic ice maker repair in all 5 West End, Crafton & the Airport Corridor ZIP codes: diagnosis in your home, then a price for you to accept before anything is done.
West of the Ohio's bend, the West End runs from old city neighborhoods on steep hills through the leafy railroad suburbs of Crafton and Ingram and out along the Parkway toward the airport. Chartiers Creek winds through the middle of it, and in Carnegie the creek has flooded the low streets more than once, most memorably in September 2004. Further out, Green Tree, Scott and Collier are newer suburbs of split-levels, townhouses and apartment complexes.
On an Ice-O-Matic ice maker we check the supply line, then the fill valve, then the harvest parts, because small, hollow or cloudy cubes and poor output nearly always come down to water flow or mineral buildup. Also worth knowing: an Ice-O-Matic with slow harvests or shrinking cubes usually wants a descale or a clean condenser before it wants a part.
Call or book online and we'll set up a time that works for you.
Inside an Ice-O-Matic ice maker
An Ice-O-Matic cuber freezes water over a vertical evaporator, with a pump circulating water from a trough across the plate. An ice thickness probe senses when the ice has built to the set size and signals the board to harvest; hot gas then warms the evaporator so the slab of cubes drops into the bin. Water level sensing in the trough controls how much water each cycle uses, and a bin control stops production when the bin is full. When scale coats the evaporator or the probe, harvest timing goes wrong: cubes grow too thick, stick, or release as a single sheet. Pearl Ice and flaker models use an auger instead, with their own wear points in the gear motor and bearings.
One more point: sticking to a regular clean-and-sanitize routine is what keeps these cubers producing.
Common Ice-O-Matic ice maker failures
What we look at first on this pairing: Scale on evaporator and thickness probe; Water pump weak; Ice thickness probe dirty or misadjusted; Bin control not sensing full; Water inlet valve failing.
That's where we start, not a verdict. The same complaint can come from an inexpensive part or a costly one, which is why the cause is confirmed in your home before any price is given.
Ice-O-Matic ice makers in West End, Crafton & the Airport Corridor homes
Around West End, Crafton & the Airport Corridor a ice maker could be anything from a panel-fronted built-in in a restored house to a bare-bones unit in a rental; we ask for the model number first because it tells us which platform we're dealing with.
A ice maker that stood in floodwater in West End, Crafton & the Airport Corridor should stay unplugged until its compressor wiring, fan motors and controls have been checked.
The ice maker fault people misjudge
Across brands, the ice maker symptom that misleads people most is an ice maker declared dead when the real problem is a line crushed behind the refrigerator, a line frozen along an outside wall, or a fill-valve screen clogged with scale.
In West End, Crafton & the Airport Corridor, the local condition that matters most for a ice maker is long water lines run up from the basement through the kitchen floor, lines that freeze in a cold snap, and scale collecting in the fill valve.
Power outages and food
After a long outage, give the refrigerator several hours to pull back down to temperature before deciding it has failed. Throw out the first batches of ice, and check that the ice maker restarted.
If a unit is still warm the next day, or a washer, dishwasher or range shows a blank display, call us with the model number. Surge damage to a board or power supply is common and often repairable.
Ice-O-Matic Ice Maker in West End, Crafton & the Airport Corridor, by the numbers
Ice-O-Matic Ice Maker: Questions We Hear
Quick answers to what people ask most. If yours isn't here, bring it up on the phone or type it into the notes box when you book.
Something else on your mind?
Reach out with the brand, the symptom and a model number if you have one. Some questions we can answer on the spot; the rest a technician can check in person.
Yes. Alongside household appliances, we work on reach-in coolers and freezers, prep tables, ice machines and commercial ranges and ovens for businesses in West End, Crafton & the Airport Corridor, and we try to schedule around your service hours.
Partly. Sheraden, Esplen, Windgap, Chartiers, Crafton Heights and Westwood are City of Pittsburgh neighborhoods. Crafton, Ingram, Green Tree, Carnegie and Heidelberg are boroughs, and Neville, Scott and Collier are townships. Either way, all 5 ZIP codes here are on our service map.
That depends on what broke. A switch, valve, pump or element is a small fraction of what a control board or sealed-system job runs; you get the figure once it's diagnosed and before any work.
Often, if we have the model number beforehand. Ice-O-Matic shares a parts bin with the other Commercial brands, so compatible parts are usually easy to get, even for older units. Parts that must be ordered come with a lead time you hear before deciding.