Kenmore dryer repair
Kenmore Dryer Repair in Penn Hills & Plum, PA
We test your Kenmore dryer where it's installed in Penn Hills & Plum, name the part that failed, and quote before any repair.
Rather type than call? Add the kenmore dryer's model number and where you are in Penn Hills & Plum, and we'll check parts before the visit.
Two quick steps: what's wrong and where you are. We'll be in touch to set a time.
dryer brands we repair
Kenmore Dryer Repair in Houses, Apartments and Rentals
Coverage here takes in ZIPs 15235, 15239. We work independently and aren't affiliated with Kenmore, so a unit still under the maker's warranty should go to Kenmore first. Keep the model number close by when you get in touch.
How a Dryer Repair Visit Works
Describe the Problem
The brand, the model number if it's handy, and what the appliance is doing. A photo of the rating label is a bonus.
Diagnosis On Site
The technician tests the appliance and its power, water, drain, gas or vent until the failed part is found.
Explanation and Quote
You hear what failed and what the repair costs, then decide. Nothing starts without your OK.
Repair and Test
The part goes in, the appliance runs a cycle, and you see that it works before we leave.
Related Services
Other appliances, brands and places we cover.
Kenmore Dryer Symptoms We Track Down
The same complaint can come from more than one part. We test on site to find which one before quoting.
- Not Heating
- Drum Not Tumbling
- Takes Too Long to Dry
- Making Loud Noise
- Won't Start
- Dryer Overheating
- Not Drying Clothes
- Shutting Off Early
- Not Getting Hot Enough
- Taking Too Long to Dry
- Thermal Fuse Blown
- Heating Element Burned Out
- Gas Igniter Not Working
- Gas Valve Solenoid Failure
- Flame Sensor / Radiant Sensor Failure
- Blower Wheel Clogged with Lint
- Exhaust Duct Clogged
- Restricted Exhaust Airflow
- Dryer Venting Improperly
- Drive Belt Broken
- Drum Rollers Worn Out
- Drum Glide / Bearing Worn
- Idler Pulley Seized
- Drive Motor Failure
- Making Loud Noise During Operation
- Squealing Noise During Tumble
- Thumping or Banging Noise
- Rattling Noise
- Control Board Failure
- Cycling Thermostat Failure
- High-Limit Thermostat Failure
- Moisture Sensor Failure
- Dryer Door Not Closing Properly
- Door Switch Failure
- Lint Trap / Screen Damaged
- Start Button Not Working
- Dryer Won't Turn On
- Tripping Circuit Breaker
- Burning Smell
- Clothes Shrinking
- Clothes Still Wet After Full Cycle
- Clothes Damp but Warm After Cycle
- Auto-Dry Sensor Not Working
- Timer Not Advancing
- Electric Dryer No Heat — Partial Power
- Gas Smell from Gas Dryer
- Display Panel Not Working
- Buttons Not Responding
- Won't Spin at All
- Stops Mid-Cycle
- Heat Setting Not Changing
- Excessive Energy Use
- Excessive Static on Clothes
- Clothes Heavily Wrinkled
- Steam Function Not Working
- Moisture Sensor Needs Cleaning
- Exhaust Hose Kinked
- Exterior Too Hot to Touch
- Wrinkle-Prevent Tumble Not Working
- Requires Two or More Cycles to Dry
- Error Code on Display
- Low Gas Pressure to Dryer
- Drum Interior Light Not Working
- Door Handle Broken
- Auto-Dry Cycle Runs All Night
- Gas Burner Orifice Clogged
- Lint Fire Hazard in Ductwork
- Timer Advancing Too Slowly
- Three-Prong Outlet / Four-Prong Cord Mismatch
- Knocking at Startup
- Intermittent Squeaking
- Bird or Pest Nest in Dryer Duct
- Cycling Thermostat Stuck Closed
- Gas Valve Solenoid Kit Needed
- Thermal Cutout Needs Resetting
Dryer Makes We Also Repair
More Kenmore Products
About Kenmore dryer repairs here
Kenmore dryer repair in all 2 Penn Hills & Plum ZIP codes: diagnosis in your home, then a price for you to accept before anything is done.
Penn Hills and Plum are where the eastern suburbs spread out. Penn Hills filled in after the war with brick ranches and split-levels on winding streets, while Plum grew later, with newer subdivisions and houses on bigger lots. In both, the kitchen is rarely the problem spot; it's the lower level, where the washer, the dryer, the second refrigerator and the chest freezer share space with a garage door that lets in the cold.
On a Kenmore dryer we check the path the air takes out of the house before anything electrical, meaning the vent, the flexible hose behind the machine and the lint route are all checked ahead of the element or the fuse, because a smothered vent is usually what killed the last one. Also worth knowing: once the real manufacturer is known, a Kenmore is serviced the same way as that maker's own models.
Call or book online and we'll set up a time that works for you.
Inside a Kenmore dryer
A Kenmore dryer with a 110 prefix is a Whirlpool design inside, most often the familiar 29-inch platform with a thermal fuse, a high-limit and cycling thermostat, rear drum rollers, a front drum glide, a belt and an idler pulley. Electric models use a heating element in a housing; gas versions light with a glow bar and open the burner through a pair of valve coils. The 796-prefix dryers are LG designs with their own sensors and boards. On any of them, the most common heat fault starts at the vent. In an older house, long vent runs through basement joists or an exterior wall hood that frosts or clogs in winter cut airflow, overheat the dryer, and blow the thermal fuse.
One more point: Kenmore was a Sears label, and Whirlpool, LG, Electrolux, GE and others built the machines; the digits in front of the dot in the model number reveal which.
Common Kenmore dryer failures
What we look at first on this pairing: Thermal fuse blown by a restricted vent; Heating element open; Gas valve coils weak; Drum rollers or idler pulley squealing; Drum belt broken.
That's where we start, not a verdict. The same complaint can come from an inexpensive part or a costly one, which is why the cause is confirmed in your home before any price is given.
Kenmore dryers in Penn Hills & Plum homes
Split-levels and ranches in Penn Hills & Plum often put the dryer in the middle of the house, with a long vent across a finished ceiling. Lint gathers out of sight, so we measure the airflow before suspecting the heater.
In a damp basement in Penn Hills & Plum, a dryer whose hose has slipped off blows warm, wet air into the room; check both ends are clamped.
The dryer fault people misjudge
Across brands, the dryer symptom that misleads people most is a dryer that has been given a new heating element two or three times while the clog that burned out the first one is still sitting in the vent.
In Penn Hills & Plum, the local condition that matters most for a dryer is vent runs that cross a basement ceiling and exit through stone or block, and outside hoods whose flaps freeze shut in the cold.
Power outages and food
After a long outage, give the refrigerator several hours to pull back down to temperature before deciding it has failed. Throw out the first batches of ice, and check that the ice maker restarted.
If a unit is still warm the next day, or a washer, dishwasher or range shows a blank display, call us with the model number. Surge damage to a board or power supply is common and often repairable.
Kenmore Dryer in Penn Hills & Plum, by the numbers
Kenmore Dryer: Questions We Hear
Quick answers to what people ask most. If yours isn't here, bring it up on the phone or type it into the notes box when you book.
Something else on your mind?
Reach out with the brand, the symptom and a model number if you have one. Some questions we can answer on the spot; the rest a technician can check in person.
Yes, while it's under the manufacturer's warranty. Warranty repairs are normally handled by the maker's own service network, and we're an independent company, not an authorized service center. Once the warranty has run out, or the problem isn't covered, we're glad to take the job in Penn Hills & Plum.
Usually. When you book a Penn Hills & Plum visit, list every appliance that's giving trouble, with model numbers if you have them, so we set aside enough time and bring the likely parts.
That depends on what broke. A switch, valve, pump or element is a small fraction of what a control board or sealed-system job runs; you get the figure once it's diagnosed and before any work.
Often, if we have the model number beforehand. Kenmore models came from several different factories, so the model number is the only way to know which parts fit. Parts that must be ordered come with a lead time you hear before deciding.